How to sterilize centrifuge bottles or tubes？

Operating conditions: 121°C / 15 psig (1 bar), 20 minutes at a time. PP/PPCO/PMP/FEP and ETFE products can be sterilized several times under normal conditions. PC and PSF containers can also be sterilized at high temperature and pressure under the same conditions, but their mechanical strength and service life will be reduced. If you sterilize PC or PSF products, be sure to follow the above inspection guidelines.

How to clean used centrifuge tubes or bottles?

Step 1: Soak in non-alkaline detergent remove the tightly adhering residue pH neutral cleaning solutiona void corrosion by alkaline substancese specially polycarbonate (PC) products Step 2: Non-abrasive brush scrubbing Remove residues using a rubber or fluoropolymer brush to avoid scratching or excessive wear of the centrifuge equipment. Step 3: For the final rinse, use distilled water. Step 4: Wind drying

How should centrifugal instruments be handled after use?

1. If it's a disposable centrifugal instrument, please discard it immediately 2. If the centrifuge has been used with hazardous materials, please disinfect it before disposal 3. If it's a reusable centrifuge, it needs to be carefully cleaned according to the steps provided

Carefully inspect the centrifuge tubes and centrifuge bottles before each use

At high speeds, the centrifuge experiences very strong centrifugal forces, which can cause the appliance to rupture. To ensure safe laboratory operation, all centrifuges should be inspected before each use. How to check? Plastic centrifuges are easy to inspect and do not require special equipment. Before placing the tube at an angle to the light, observe initial signs of excessive stress on the plastic, such as darkening, discoloration, or visible "cracks" (visible slits). Over time, these cracks will widen and eventually render the tube unusable.

centrifuge tube, centrifuge bottle factory

Centrifuge Tube & Centrifuge Bottle

Centrifuge tubes and bottles are typically used with centrifuges for the preparation and separation of laboratory samples. There are many types of centrifuge tubes and bottles, and the appropriate material, capacity, maximum centrifugal force, and bottom type should be chosen based on specific use cases. GlanLab Instrument is a manufacturer with over 20 years of experience in producing centrifuges. The company also offers a wide range of centrifuge accessories that are compatible with most centrifuges worldwide.

You are here: Home » Products » Centrifuge Tubes/Bottles

Product Customization Services

SELECTED MATERIAL

Provide FEP，ETFE,PPCO,PC，PE，PPPSF various materialsfor option.The smoothinner wall wouldreduce the shearforce on the cells.

SCREW CAP CENTRIFUGETUBES/BOTTLES

The screw cap centrifuge is molded at one time.Thesealing ring is molded inside the cover, and is pressed andfitted with the inner surface of the bottle neck, moreover,the sealing pad can be sealed without sealing. The bottleand cap are made of continuous straight shoulder semi-trapezoidal threads to ensure smooth screwing, stronglocking force and tight sealing. The neck and shoulderswere modified on the basis of the original old-fashionedcentrifuge tubes/bottles(common on the originalcentrifugal rotor). lt makes the pouring of liquid smooth andconvenient, and at the same time can withstand highecentrifugal force, improve service life and safety.

GLAND TYPE CENTRIFUGETUBES/BOTTLES

Adopt one time injection molding technology with specialrigid material,which can withstand higher centrifugal force.The inner wall surface is silicified and with anti-statictreatment, and can obtain better centrifugal effect. Thegland is specially designed to ensure that the gas issmoothly discharged when the cover is closed, that the airis not deflated, so that the cover cannot be closed, andthat a certain airtightness is ensured to prevent leakage.The special cover for the pick-and-place handle isdesigned on the gland, which greatly facilitates the pick-and-place of the centrifugal device in the rotor.

ADVANCED TECHNOLOGY

Utilize the mostadvanced casting,drawing and blowingprocesses to ensureunifomm weight , unifommwall thickness , and easyto clean inner comersfor all centrifuge tubes/bottles.

Centrifuge Tube & Bottle FAQs

How to sterilize centrifuge bottles or tubes？

Operating conditions: 121°C / 15 psig (1 bar), 20 minutes at a time.

PP/PPCO/PMP/FEP and ETFE products can be sterilized several times under normal conditions. PC and PSF containers can also be sterilized at high temperature and pressure under the same conditions, but their mechanical strength and service life will be reduced. If you sterilize PC or PSF products, be sure to follow the above inspection guidelines.
How to clean used centrifuge tubes or bottles?

Step 1: Soak in non-alkaline detergent
remove the tightly adhering residue pH neutral cleaning solutiona void corrosion by alkaline substancese specially polycarbonate (PC) products
Step 2: Non-abrasive brush scrubbing
Remove residues using a rubber or fluoropolymer brush to avoid scratching or excessive wear of the centrifuge equipment.
Step 3: For the final rinse, use distilled water.
Step 4: Wind drying
How should centrifugal instruments be handled after use?

1. If it's a disposable centrifugal instrument, please discard it immediately
2. If the centrifuge has been used with hazardous materials, please disinfect it before disposal
3. If it's a reusable centrifuge, it needs to be carefully cleaned according to the steps provided
Carefully inspect the centrifuge tubes and centrifuge bottles before each use

At high speeds, the centrifuge experiences very strong centrifugal forces, which can cause the appliance to rupture. To ensure safe laboratory operation, all centrifuges should be inspected before each use.

How to check?
Plastic centrifuges are easy to inspect and do not require special equipment. Before placing the tube at an angle to the light, observe initial signs of excessive stress on the plastic, such as darkening, discoloration, or visible "cracks" (visible slits). Over time, these cracks will widen and eventually render the tube unusable.

centrifuge tubes & bottles

500ml Conical Centrifuge Bottle

250ml Conical Centrifuge Bottle

15 Ml Conical Centrifuge Tube

Gland Type Micro Centrifuge Tube

500ml Centrifuge Bottle

250ml Centrifuge Bottle

750ml Flat Bottomed Centrifuge Bottle

500ml High Speed Centrifuge Bottle

85ml Polycarbonate Conical Centrifuge Tube

500ml Centrifuge Bottle RCF 25000

1000ml Low Speed Centrifuge Bottle

250ml Transparent Plastic Centrifuge Bottle

500ml Transparent Plastic Centrifuge Bottle

1000ml Transparent Plastic Centrifuge Bottle

500ml Low Speed Centrifuge Bottle

5ml/20ml/30ml/50ml Gland Type Centrifuge Tube

50 Ml Conical Centrifuge Tube

Gland Type Micro High Speed Centrifuge Tube

50ml Polycarbonate Centrifuge Tube Transparent

15ml Polycarbonate Conical Centrifuge Tube